Elektro-Hebezeug mit Überlastschutz

Understanding the Danger of Overload

Overloading occurs when the weight applied to the hoist exceeds its designated Working Load Limit (WLL). Die Folgen sind schwerwiegend:

• 1. Mechanischer Fehler: Critical components like the hoist motor, Getriebe, Drahtseil, Haken, or load chain experience stresses beyond their design limits, leading to breakage, distortion, or sudden failure.
• 2. Dropped Loads: A catastrophic failure often results in the load plummeting uncontrollably.
• 3. Structural Damage: The sudden shock or impact of a failure can damage the supporting structure (Strahl, crane, Portal) or surrounding equipment.
• 4. Personnel Injury: Workers in the vicinity are at extreme risk from falling objects, whipping cables/chains, or structural collapse.
• 5. Costly Downtime: Repairing or replacing damaged equipment and investigating incidents leads to significant production delays and financial losses.

The Role of the Overload Protection Device

An Overload Protection Device acts as a vigilant electronic or mechanical “guardian,” constantly monitoring the load being lifted. Its primary function is to prevent the hoist from operating if the load exceeds a pre-set safety threshold, typically set slightly above the WLL (Z.B., 105-125%, depending on standards and design) but well below the point of structural failure.

How Overload Protection Devices Work (Common Types)

• 1. Electronic Load Cells:

  • Mechanism: Strain gauges mounted within the load path (Z.B., integrated into the hook block, shackle, or the hoist structure itself) measure the force (laden) applied. This force causes minute deformations in the load cell, changing the electrical resistance of the strain gauges.
  • Signal Processing: The change in resistance is converted into an electrical signal proportional to the load.
  • Kontrolle: A control unit (often integrated into the hoist’s pendant or control system) receives this signal. If the load exceeds the pre-set limit, the control unit instantly cuts power to the hoist’s lifting motor, preventing any further upward movement. An audible and/or visual alarm is typically activated simultaneously.

• 2. Mechanical Torque Limiters:

  • Mechanism: These are often friction-based clutches installed within the hoist’s drive train (Z.B., between the motor and gearbox).
  • Operation: When the torque required to lift the load exceeds the clutch’s calibrated slip torque (directly related to the load), the clutch slips or disengages. This prevents the motor from transferring excessive force to the gearbox and lifting mechanism.
  • Aktion: While it stops the lift, it usually requires manual resetting after an overload event. May not provide an immediate electrical signal for alarms or system integration.

Key Benefits of Electric Hoists with Integrated OPDs

• 1. Verbesserte Sicherheit: The paramount benefit. Prevents catastrophic overloads, Schutz des Personals, Ausrüstung, and infrastructure. It’s a fundamental layer in a safety management system.
• 2. Asset Protection: Safeguards the expensive hoist, Drahtseil/Kette, Haken, and supporting structures from damage caused by misuse or accidental overloading. Extends equipment lifespan.
• 3. Reduzierte Ausfallzeiten: Prevents breakdowns and accidents caused by overloads, minimizing costly production interruptions and repair expenses.
• 4. Operational Compliance: Meets stringent safety regulations and industry standards (Z.B., OSHA, ANSI/ASME B30.16 – Safety Standard for Overhead Hoists) that mandate overload protection for lifting equipment.
• 5. Operator Confidence: Provides operators with a crucial safety net, allowing them to focus on the task with greater assurance.
• 6. Prevention of Minor Overloads: Even loads slightly exceeding the WLL, repeated over time, cause cumulative damage (“invisible overload”). An OPD prevents this insidious wear.

Important Considerations

• 1. Not a Substitute for Proper Use: An OPD is a critical safety feature, but it does not eliminate the need for proper operator training, adherence to load charts, regular inspections, and safe rigging practices.
• 2. Calibration & Wartung: OPDs, especially electronic load cells, require periodic calibration by qualified personnel to ensure accuracy. Mechanical limiters also need inspection and maintenance. Follow the manufacturer’s schedule rigorously.
• 3. Setting Accuracy: The overload cut-off point must be correctly set according to the hoist’s WLL and relevant standards. Never tamper with or disable the OPD.
• 4. False Trips: Environmental factors (extreme temperatures, moisture) or electrical interference can occasionally cause false trips. While inconvenient, they are a safety feature. Investigate the cause promptly.
• 5. Type Selection: Choose the OPD type (electronic vs. mechanisch) based on the application’s criticality, required features (Z.B., data logging, integration with crane control systems), environment, and budget. Electronic systems generally offer more features and precision.

Ein elektrischer Hebezeug equipped with a reliable Overload Protection Device is not merely a piece of equipment; it’s a commitment to safety, operational integrity, and responsible material handling. By acting as an automatic and fail-safe barrier against the dangers of overloading, the OPD plays a vital role in preventing accidents, protecting valuable assets, and ensuring a safer, more productive work environment. Investing in hoists with robust, well-maintained overload protection is an investment in people, productivity, und Seelenfrieden. Never lift without it.