Посібник з усунення несправностей електричної лебідки

Електрична таль – важлива частина обладнання для підйому важких вантажів. Як і будь-який складний електромеханічний пристрій, it can experience issues ranging from simple operational mistakes to serious mechanical failures. Learning to troubleshoot common problems can save you valuable time and money, while ensuring a safe working environment. This guide will walk you through the steps of diagnosing and resolving the most frequent electric hoist malfunctions.

Essential Precautions

Before you begin any troubleshooting:

• 1. Відключити живлення: Always isolate the hoist from its power source. Lock out and tag out the circuit to prevent accidental re-energizing.
• 2. No Load Testing: Never attempt to troubleshoot a hoist under load. Lower the load to a secure resting place before inspection.
• 3. Personal Protective Equipment (ЗІЗ): Wear appropriate safety gear, including gloves and safety glasses.
• 4. Знайте свої межі: If the problem involves major electrical components, structural integrity, or the brake system, consult a qualified technician. Your safety is paramount.

Common Electric Hoist Problems and Solutions

Here is a structured guide to diagnose and fix common hoist issues.

1. Hoist Does Not Operate At All

Symptoms:

• No movement in either direction (up or down).

• No sound from the motor or contactors.

Possible Causes & Solutions:

• 1. Power Supply Issue: This is the most common cause.
  • Check: Ensure the main disconnect is ON. Verify that the hoist is plugged in correctly (якщо застосовно). Test the outlet or circuit breaker with a voltmeter.
  • Solution: Reset tripped breakers or replace blown fuses. Ensure the power cord is not damaged.
• 2. Open/Limit Switch Engaged:
  • Check: Most hoists have an emergency stop or master switch that might be in the “OFF” position. Also, the upper limit switch may have been triggered, cutting power.
  • Solution: Ensure all switches are in the “ON” or reset position. Manually reset the limit switch (consult your hoist’s manual for the specific procedure).
• 3. Faulty Pendant Control:
  • Check: Inspect the pendant cord for cuts, тріщина, або пошкодження. The buttons may be stuck or faulty.
  • Solution: Have a qualified electrician test the pendant for continuity. Replace the pendant if necessary.

2. Hoist Operates in One Direction Only

Symptoms:

• The hoist lifts but doesn’t lower, or vice versa.

Possible Causes & Solutions:

• 1. Faulty Control Button:
  • Check: The button for the non-working direction on the pendant may be damaged or have a broken wire.
  • Solution: Test the pendant control. Replacement of the button or the entire pendant is often required.
• 2. Stuck or Faulty Contactor:
  • Check: The contactor (a heavy-duty relay) for one direction may have failed, burnt contacts, or a faulty coil.
  • Solution: This requires a qualified technician to diagnose and replace the faulty contactor.
• 3. Limit Switch Issue (for the raising direction):
  • Check: The upper limit switch might be malfunctioning and not resetting, preventing the hoist from lifting further, even if it’s not at the limit.
  • Solution: Оглядати, test, and reset or replace the limit switch.

3. Motor Humms But Doesn’t Run

Symptoms:

• A loud humming or buzzing sound comes from the motor, but the chain or hook doesn’t move.

Possible Causes & Solutions:

• 1. Низька напруга:
  • Check: Use a voltmeter to check the voltage at the hoist’s connection point. It should be within 10% of the rated voltage.
  • Solution: Correct the power supply issue. Low voltage can seriously damage the motor.
• 2. Втрата фази (for 3-Phase Hoists):
  • Check: A blown fuse or broken wire can cause a loss of one phase.
  • Solution: A technician must check all fuses and wiring for the power supply.
• 3. Mechanical Jam or Overload:
  • Check: The load might be beyond the hoist’s capacity, or an internal mechanism (шестерні, підшипники) may be seized.
  • Solution: Immediately turn off power. Check for a jammed load or obstruction. Do not force the hoist. If the mechanism is seized, professional repair is needed.

4. Hoist Struggles or Runs Slowly Under Load

Symptoms:

• Motor speed is significantly reduced when lifting a load.

Possible Causes & Solutions:

• 1. Низька напруга:
  • Check: As above, low voltage is a common culprit for poor performance.
  • Solution: Ensure adequate voltage supply.
• 2. Перевантаження:
  • Check: The load may be too heavy for the hoist.
  • Solution: Never overload a hoist. Check the weight of the load and ensure it is within the hoist’s rated capacity. Overloading is extremely dangerous and can cause catastrophic failure.
• 3. Worn Motor or Brake Drag:
  • Check: Internal motor issues or a brake that is not fully releasing can create excessive drag.
  • Solution: Requires inspection and repair by a technician.

5. Надмірний шум під час роботи

Symptoms:

• Grinding, rattling, or screeching sounds during movement.

Possible Causes & Solutions:

• 1. Lack of Lubrication:
  • Check: Gears and mechanical joints may be dry.
  • Solution: Refer to the manufacturer’s manual for the correct lubrication points and type of lubricant. Do not over-lubricate.
• 2. Worn or Damaged Gears/Bearings:
  • Check: Internal mechanical components wear out over time.
  • Solution: These components need to be replaced by a professional.
• 3. Loose Parts or Mounting:
  • Check: Inspect the entire system, including the mount, гачки, and guards, for loose bolts or parts.
  • Solution: Tighten all fasteners to the manufacturer’s specified torque.

Коли викликати професіонала

While basic checks are fine, certain problems require expert attention:

• 1. Any internal electrical issue (контактори, motor windings).

• 2. Any problem with the brake assembly.

• 3. Any structural damage to the hook, ланцюг, or housing.

• 4. Any gear or bearing replacement.

• 5. If you are unsure of the cause or the solution.

Preventive Maintenance is Key

The best troubleshooting is avoiding problems altogether. Establish a regular preventive maintenance schedule:

• 1. Візуальний огляд: Daily check for loose bolts, damaged hooks, worn chain, and cord damage.
• 2. Functional Test: Test the hoist without a load daily, checking all directions and limit switches.
• 3. Regular Lubrication: Lubricate as per the manufacturer’s schedule.
• 4. Professional Inspection: Have a certified technician perform an annual inspection.

By using this electric hoist troubleshooting guide, you can confidently address common issues, maintain a safer workspace, and keep your operations running smoothly. Запам'ятати: коли є сумніви, always err on the side of caution and call a qualified expert.